guides:virtual_modem:section_4
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
guides:virtual_modem:section_4 [2020-02-18 18:01] omolini [Initial VModem testing] |
guides:virtual_modem:section_4 [2020-02-19 02:10] omolini [Skip to other sections] |
||
|---|---|---|---|
| Line 26: | Line 26: | ||
| * Make sure they are executable: | * Make sure they are executable: | ||
| - | * chmod 770 /boot/vmodem/vmodem.sh | + | <code bash> |
| - | * chmod 770 /boot/vmodem/1.sh | + | chmod 770 /boot/vmodem/vmodem.sh |
| - | * chmod 770 /boot/vmodem/ppp.sh | + | chmod 770 /boot/vmodem/1.sh |
| + | chmod 770 /boot/vmodem/ppp.sh | ||
| + | </code> | ||
| ==== Name of the serial port ==== | ==== Name of the serial port ==== | ||
| The VModem script has been preconfigured to use **ttyUSB0** as the default serial port name. Typically Raspbian will call its first serial port adapter **ttyUSB0** when using USB to Serial converters, and you won't need to modify this script. However, if the name is something **different**, such as **ttyAMA0**, you may need to update the script to point to the correct serial port name. The following section described how to double-check your serial port name: | The VModem script has been preconfigured to use **ttyUSB0** as the default serial port name. Typically Raspbian will call its first serial port adapter **ttyUSB0** when using USB to Serial converters, and you won't need to modify this script. However, if the name is something **different**, such as **ttyAMA0**, you may need to update the script to point to the correct serial port name. The following section described how to double-check your serial port name: | ||
| Line 67: | Line 70: | ||
| * Over on the Raspberry Pi, you should be seeing the corresponding output: | * Over on the Raspberry Pi, you should be seeing the corresponding output: | ||
| {{ :guides:pics:vmodem_putty2.png |}} | {{ :guides:pics:vmodem_putty2.png |}} | ||
| - | ==== Troubleshooting ==== | ||
| - | |||
| - | * Some computers are not cabable of operating at fast serial speeds. If you're unable to connect at 28800 or faster, try slower speeds, such as 9600 baud at first. Adjust both the vmodem.sh script to 9600 and your modem serial speed to connect at 9600 baud. If that works, then work your way up to see where the limit for your specific computer is. | ||
| - | * If you run into any other issues, take a note of them and look for commonalities in any steps you've taken before this step. Open up the script vmodem.sh for editing to make sure the baud and serial port are properly set. If you're unable to figure it out, feel free to contact me (see bottom of page). | ||
| ===== Getting online ===== | ===== Getting online ===== | ||
| Line 110: | Line 109: | ||
| * [[Guides:Connecting a Dumb/Smart Terminal to the Internet]] | COMING SOON | * [[Guides:Connecting a Dumb/Smart Terminal to the Internet]] | COMING SOON | ||
| - | ==== Skip to other sections ==== | + | ===== Troubleshooting ===== |
| + | |||
| + | * Some computers are not capable of operating at fast serial speeds. If you're unable to connect at 57600 or faster, try slower speeds, such as 9600 baud at first. Adjust both the vmodem.sh script and the computer to connect at only 9600 baud. If that works, work your way up to see where the limit for your specific computer is. | ||
| + | * If you run into any other issues, take a note of them and look for commonalities in any steps you've taken before this step. Open up the script vmodem.sh for editing to make sure the baud and serial port are properly set. If you're unable to figure it out, feel free to contact me (see bottom of page). | ||
| + | |||
| + | ==== Skip to previous sections ==== | ||
| * [[Guides:Virtual Modem|Section 1 - Introduction]] | * [[Guides:Virtual Modem|Section 1 - Introduction]] | ||
guides/virtual_modem/section_4.txt · Last modified: 2023-11-24 23:16 by omolini
Page Tools
